-Ancillary Equipment
!
AlertA Gamma
Weight: kg

AC Powered Amplified Telephone Ringer

NEW Product Mains Powered Loud Sounding Alarm Suit Two Wire Analogue Telephones, Internal Speaker produces 103db. Internal LED visual Alert.

Can also have External Horn ( 108db ) using HSP15  & External Strobe attached ( see items below )

Higher outputs are possible depending on model of external speaker. Up to 115db

Note; This Unit CAN operate from 12 Volt DC Battery / Solar Systems ( Call for Details )

See Demonstration at this web address;

http://www.youtube.com/watch?v=JocoQ7AXMqg 

Toggle Relay
Weight: kg

Toggle Relay Board

NEW

Toggle / Latching relay Board.

Changes state each time a input is pulsed, and remains in that state until same input is pulsed again.

Use Ring detect relay ( Ringmate 12-24 or AlertA Gamma ) to change state.

Board size is 105mm x 55mm fits into Jiffy Box ( not supplied )

Output Relay contacts are Single pole Change over  rated @ 240VAC 7 amps

HSP2
Weight: kg

135mm 15 Watt Horn Speaker

White plastic, 8 Ohm Weather proof, swivel bracket included. 

Strobe BLUE
Weight: kg

Strobe BLUE

12 Volt DC Xenon Strobe 95mm Diameter

Stands 80mm High Draws 220 mAmp

Lead is 550mm long, Attached to surfaced via 2 Long Screws ( Supplied ) from under the lens.

Strobe CLEAR
Weight: kg

Strobe CLEAR

12 Volt DC Xenon Strobe 95mm Diameter

Stands 80mm High Draws 220 mAmp

Lead is 550mm long, Attached to surfaced via 2 Long Screws ( Supplied ) from under the lens.

Strobe RED
Weight: kg

Strobe RED

12 Volt DC Xenon Strobe 95mm Diameter

Stands 80mm High Draws 220 mAmp

Lead is 550mm long, Attached to surfaced via 2 Long Screws ( Supplied ) from under the lens.

Strobe AMBER
Weight: kg

Strobe AMBER

12 Volt DC Xenon Strobe 95mm Diameter

Stands 80mm High Draws 220 mAmp

Lead is 550mm long, Attached to surfaced via 2 Long Screws ( Supplied ) from under the lens.

12-48 & HSP15
Weight: kg
Larger picture

Type C Loud Sounding Alarm & speaker

Two (2) Line Inputs, Volume Control 113db Output

Wallmount, 240VAC operation, 150mm 15 Watt Horn Speaker Included

A larger tone ringer providing 15 watts of power in response to the telephone ringing signal. This product is intended for noisy industrial environments and when large coverage is required. There is NO internal speaker.

This Tone Ringer "C" requires the use of an external horn loud speaker such as type HSP15, which is a 150mm (6') unit.

ACA Permit No. C89/2/219

12-48
Weight: kg
Larger picture

Type C control unit ONLY

Two (2) Line Inputs, Volume Control 113db Output

Wallmount, 240VAC operation,

A larger tone ringer providing 15 watts of power in response to the telephone ringing signal. This product is intended for noisy industrial environments and when large coverage is required. There is NO internal speaker.

This Tone Ringer "C" requires the use of an external horn loud speaker such as type HSP15, which is a 150mm (6') unit.

Note: If the product is required including the horn loud speaker, the combined unit is described as a "Loudsounding Alarm". Part No ; 12/48 & HSP15 ( see above )  Manufactured to Australian Specifications.

ACA Permit No. C89/2/219

AlertA Alpha
Weight: kg

Telephone Ringer Standard

" NEW " Low cost

FEATURES-
Line Powered
Audible  Ringing from an analogue line
Internal Speaker 
90 Decibel Output Maximum
Adjustable Volume Control
Adjustable Pitch control
Wall Mountable with OR without standard telephone wall plate.
Parallel Line Socket
ACA approved

Specifications
Maximum Sound Pressure:  90 db @ 1 Metre ( Nominal )
(AC Ring to be in the range 70 to 95 VAC RMS )
Control Unit Dimensions: 112mm x 133mm x 58mm
Internal Speaker  ,Shipping Weight: 500 Gram
Connections: 2 x RJ12 6P2C, Parallel Sockets       REN=1

NOTE THE RING OF UNIT IS THE SAME VOLUME AS A STANDARD TELEPHONE

Note; Output Volume is DEPENDANT on Ring Voltage on line, Eg; Number of phones, Length of phone line, PABX / Key System ring voltage.

AlertA -Beta
Weight: kg

HIGH Output Telephone Ringer

" NEW "  HIGH POWER

FEATURES-
Line Powered
Loud Piezoelectric Ringing from an analogue line
Internal Speaker 
102 Decibel Output Maximum
Adjustable Volume Control
Adjustable Pitch control
Wall Mountable with OR without standard telephone wall plate.
Parallel Line Socket
ACA approved

Specifications
Maximum Sound Pressure: 102 db @ 1 Metre ( Nominal )
(AC Ring to be in the range 70 to 95 VAC RMS )
Control Unit Dimensions: 112mm x 133mm x 58mm
Internal Speaker  ,Shipping Weight: 500 Gram
Connections: 2 x RJ12 6P2C, Parallel Sockets       REN=1

Note; Output Volume is DEPENDANT on Ring Voltage on line, Eg; Number of phones, Length of phone line, PABX / Key System ring voltage.

K3507
Weight: kg
Larger picture

Tone Ringer Type A "Access Brand"

Line powered 2 wire Analog approx 89bd output, ON/OFF switch, Volume and PITCH controls.

External speaker optional ( Recommend Model HSP2  92db Output see above )

Note; Output Volume is DEPENDANT on Ring Voltage on line, Eg; Number of phones, Length of phone line, PABX / Key System ring voltage.

RM Strobe+
Weight: kg
Larger picture

Ringmate Strobe Plus

Visual Ringer Strobe unit plugs into Analog telephone line, 240VAC operation, 90mm dia x 80mm high strobe, { Choice of Blue or Amber, Clear, Red }

 

RM 12-24
Weight: kg
Larger picture

Ring Detect Relay 50 Volt "Ring Mate 12-24"

Detects ringing on a analog telephone line causing relay contacts to operate, Max 50VDC @ 2 Amp

240VAC operation Plug pack supplied

Call About availability

RM 240-10 Full
Weight: kg
Larger picture

Ring Detect Relay & Doorbell "Ringmate 240-10 Full"

Detects ringing on a analog telephone line causing relay contacts to operate, Max 240VAC @ 10 Amp

Also gives differant signal when press button at door is operated.

240VAC operation Installation by Licenced contractor is required..

Approx 5 Days Delay for supply.
K3509
Weight: kg
Larger picture

LSA & STROBE Control

Two (2) Line Inputs, Volume Control Max 118db Output

Also triggers relay for connecting 12Vdc strobe.

Wallmount, 240VAC operation Plug pack supplied,

Speaker and Strobe is Optional

Note; Grill on unit is DUMMY there is no speaker behind it.
DT1
Weight: kg
Larger picture

Talking Alarm Dialer

The Dialguard DT1 dialler uses a client programmable message to report an alarm condition to any telephone anywhere in the world

Programable 15 sec message & upto 6 phone numbers.

Single Channel ( Relay contacts closing starts operation )

12VDC required ( Plugpack optional )  Wall Mount Bracket Optional 

Programming of the DT1 is done using the onboard keypad and programmed data can be replayed on the 7 segment display for confirmation. Voice information is recorded using the built in microphone and can be replayed through the onboard speaker. The display will indicate any errors made while programming. The DT1 can be cancelled by entering a 1 to 7 digit shut down code on DTMF telephones while the alarm message is playing. After the DT1 has been cancelled it will give a confirmation tone.
The DT1 can be triggered from either a positive or negative alarm source. The key switch input can also be used to disable the alarm input for times when the system is not in use or to cancel the dialler locally.
    Features of the Dialguard DT1 include:
  • 15 second user recordable voice message
  • 1 alarm input
  • Key switch input to enable/disable the alarm input
  • Programmable polarity on alarm and key switch inputs
  • Non-volatile memory stores all programmed data and voice message for 10 years without power
  • 6 user programmable phone numbers
  • Up to 6 dialling attempts at communicating an alarm condition
  • Remote shutdown of the dialler via user programmable shutdown code of between 1 and 7 digits via DTMF telephone
  • Fully programmable via the on board keypad
  • Programmed information can be verified by replaying it on the 7 segment display (numeric data) or through the on board speaker (voice data)
  • 50 millisecond debounce time on all inputs
  • Failure and error code indication
  • 12 Volt D.C. operation standard
  • 3 year warranty
  • A-Tick approved
A2710
Weight: kg

USB MP3 Player for MOH & BGM

Designed for BGM systems in commercial installations requiring audio playback from a USB memory stick. Alternatively it can be used to add MP3 playback to any domestic audio system. Simply connects to an amplifiers RCA input and provides typical CD player style functionality ie: play/pause & track skip. Tracks will automatically loop providing a constant source of background music for PA systems. Line output level volume is adjustable via the side panel. Suitable for use with USB memory sticks or SD/SDHC/CF cards when used in conjunction with a card reader. USB NOT INCLUDED.

INCLUDES 12VDC plugpack. Dimensions: 100L x 40H x 55Wmm.

Features:
Supports MP3 folder hierarchy structure ie: will browse music inside folders on stick
Compact size
Line level volume adjustment
Simple plug and play operation
Box flange allows mounting to any surface
Automatic playback looping
Starts playback immediately on power up
If power is lost, playback will recommence at last position when power is restored
DP540A
Weight: kg
Larger picture

Digital Music Recorder 18 Mins Max.

  • Flash Memory with 18 minutes storage capacity
  • Full PCM 64Kbps crystal-clear Sound Quality
  • 4 tracks available to record/play the message/music
  • 8 selectable Playing Functions
  • Voice activate recording and silence stop recording mechanism
  • Output available for PBX MOH port, Speaker, Earphone and Trunk
  • Connect External Trigger Switch available
  • Multi-application for playing promotional contents during the store promoting campaign
  • Intersperse voice message such as various announcements in school, factory, or public occasion
  • Announce event/news/product introduction/item description for cooperate, stores, trade shows, various Information centers
  • Alarm system (Emergency announcement)
  • Interactive item description in Museums
  • One for all design depending on your voice announcing demands
    • Message/Music On-Hold

    Announce pre-recorded voice messages and play elegant music to your clients while the incoming calls are on hold. To inform callers about goods and services, reinforce the image of company, convey the desired information to callers as you want. Turn passive waiting time to active promotion period.  NOTE ; Line Isolation Unit Required for MOH

    Click Here To download User Guide 52KB

    Ringmaster
    Weight: kg
    Larger picture

    Ringmaster

    Demonstrate Telephone equipment without an exchange line, Rings 2nd Extension when 1st Handpiece is lifted.

    240VAC operation Plugpack supplied.

    RingMaster STD allows you to simply connect any Telephone, Answering Machine, Modem, Fax Machine, Security Dialer or any other telephone device directly to either or both ports of the RingMaster. To initiate communication from one device to the other simply lift the handset (if fitted), begin dialing or produce an ‘off hook’ condition. RingMaster will will then ring the OTHER device with the normal 'Australian Ring Pattern' until such time as the OTHER device answers the call, or the CALLING device goes back 'On Hook'. If the the called device has answered, RingMaster will connect the two devices together with a completely ‘noise free’ path so that they can communicate. Operation of this product is fully bi-directional. This unit does not have the ability to generate Dial Tone, Busy Tone or Disconnect Tone
    Ringmaster PRO
    Weight: kg
    Larger picture

    Ringmaster PRO

    RingMaster PRO provides all the facilities of the STD model and in addition produces Australian ‘dial tone’ and ‘busy tone’ and 'disconnect tone' as appropriate, whenever an attached device produces an ‘off hook’ condition. This model also has the ability to output all SEVEN Distinctive Ring Patterns that are planned to be used in Australia (DR1 to DR7) in addition to our normal Australian ring pattern (DRO).

    RingMaster PRO
    is bi-directional in operation and responds to DTMF commands only. Simply connect your telephone devices to the modular sockets labeled Phone 1 and Phone 2. To initiate a NORMAL CALL (using the normal Australian ring pattern), simply go 'Off Hook' on EITHER device (Australian Dial Tone' will then be generated) and then dial 0. The RingMaster Pro device will then ring the OTHER device with the normal 'Australian Ring Pattern' until such time as the OTHER device answers the call, or the CALLING device goes back 'On Hook'. If the OTHER device answers the call, BOTH devices will be then be immediately connected to each other so that they can communicate. If BOTH devices are 'Off Hook' at the same time, the RingMaster Pro will generate Australian 'Busy Tone'.

    DISTINCTIVE RING GENERATION To initiate a DISTINCTIVE RING CALL (such as FaxStream Duet or Multiple Number ring), simply dial the appropriate digit from 1-7, instead of Dialing 0.

    For DISTINCTIVE RING pattern DR1 - Dial 1.(Diverted call)
    For DISTINCTIVE RING pattern DR2 - Dial 2.
    For DISTINCTIVE RING pattern DR3 - Dial 3
    For DISTINCTIVE RING pattern DR4 - Dial 4
    For DISTINCTIVE RING pattern DR5 - Dial 5
    For DISTINCTIVE RING pattern DR6 - Dial 6 (Easycall Multiple Number)
    For DISTINCTIVE RING pattern DR7 - Dial 7 (FaxStream Duet)
    C10100P
    Weight: kg

    ADSL2+ Central Splitter Filter Internal "C10"

    NEW     Internal Flush plate mount with IDC terminals,

    Central ADSL splitter, designed for ADSL/ADSL2/2+ services. Provided with an IDC terminal block, and epoxy coated suitable for mounting inside NTDs as well as external and internal installations.

    90x45x38mm Grey Colour,

    Suitable for ADSL2+

    Note; Express Delivery on (1) One or (2) Two of these filters will be $12 Ex GST

    We will adjust pricing to this at time of Packing

    C10245M
    Weight: kg
    Larger picture

    ADSL Splitter/Micro Filter "C10" Brand

    Combined Inline Filter / Splitter with RJ45 sockets supplied with RJ12 reducers and 170mm lead.

    All four conductors are connected between the 'Line' and ' Local Phone' sockets, this is required for security systems

    60x38x18mm  Now Improved Model Designed for ADSL2+

    Note; Express Delivery on Up to (5) Five of these filters will be $12 Ex GST

    We will adjust pricing to this at time of Packing

    C10645M
    Weight: kg
    Larger picture

    ADSL 610 Series Filter Splitter

    Inline ADSL Distributed Filter/Splitter with RJ45 modem, 606 plug line and 610 socket phone connectors.

    Now Improved Model Designed for ADSL2+

    C10345M
    Weight: kg
    Larger picture

    ADSL Wall Phone Filter/Splitter with RJ12 LEAD

    Combined Wall phone Filter / Splitter with RJ45 sockets supplied with RJ12 reducers. Has FLEXIBLE Connection lead with RJ12 Plug ( See Additional Images for Detail )

    Fits onto existing Wall Plate and then wall phone is hung on this filter.

    Now Improved Model Designed for ADSL2+

    114x76x18mm

    C10100E
    Weight: kg
    Larger picture

    ADSL Central Splitter/Micro Filter IP54 External Box "C10"

    External Wall mountable IP54 Box with IDC terminals, Case can be 'security' sealed.

    120x90x50mm Grey Colour,

    Suitable for ADSL2+

    Note; Express Delivery on (2) Two of these filters will be $12 Ex GST

    We will adjust priceing to this at time of Packing

    Duet Switch 1
    Weight: kg

    Budget Line Sharer for FaxStream Duet

     
  • Receive Fax Calls Automatically, just like having a separate Fax Line
  • Advertise a Separate Fax Number 
  • Save Money associated with Fax Line Installation & Rental
  • Ideal for Small Businesses currently sharing a Phone/Fax number
  • Ideal for Existing Businesses which have a little used Fax line
  • Easy User Installation
  • Note; Faxstream Duet is a Telstra Service
  • Item may differ for photo.

    Duet Switch 2
    Weight: kg

    DUET Switch for FaxSteam Duet

    Same as FAXMATE except this Model CHANGES the Ring Pattern to STANDARD Ring.

    As Some FAX Machines do not recognise the Duet Ring.

    DUET SWITCH will automatically detect this special ring pattern and answer the incoming call. It will then generate and output a Normal Ring Pattern to your fax device which will cause it to answer. Once your fax device has answered, it will then connect with the incoming fax call and receive the transmission.

    By using this method where incoming fax calls are answered first by DUET SWITCH and then a normal ring pattern is output to your fax device, we can guarantee that it will operate with almost all Fax and Fax/Modem devices. 

    More basic products such as our FAXMATE, simply redirect the incoming FaxStream Duet ring to your Fax device and require it to answer the incoming call.  This is suitable for most fax devices, but some fax devices cannot answer the short ring bursts associated with FaxStream Duet.

    DUET SWITCH also provides the following additional facilities :

    • If you have been sharing your normal number with your Fax Machine in the past, then you can expect to continue to receive Fax Calls on your main number. DUET SWITCH will allow you to receive Fax calls that may be sent on your normal voice number.
    • Will allow an Answering Machine that may be integrated with your fax device to take voice messages from your normal voice number.
    • Incorporates a set of FOUR MICRO DIP SWITCHES, which will allow the DUET SWITCH to be specially configured for use with the Telstra Calling Number Display (CLI) service and for other common telephone line sharing applications.
    DC Block LIU
    Weight: kg
    Larger picture

    DC Blocking Line Isolation Unit "NEW"

    DC Isolating or Blocking LIU Suitable for 'Music on Hold' and 'Public Address' RJ Sockets ( Changeable cords ) A tiny 54x26x24mm, Grey Colour.

    Cords available are; 3.5Mono - 3.5 Stereo - RCA - RJ12 - 6.3mm Phono.   Please specify your cord requirement. There are some limitations.

    If NOT specified we will supply 3.5 Stereo on the Music end and RJ12 on the system end.  

    Specifications:

    Limiting: 2.8V Peak to Peak when Terminated with 600ohms 
    Freq. Response: 20 to 20kHz - designed to minimise distortion.
    Input Attenuation: Selectable via volume control
    Safety Isolation: 3000V
    Connections:
      Music Input: RJ11 Socket 4P2C to 3.5mm stereo plug, with 400mm cable ( Standard ) See options
      DC Blocking Output :

     

    250 Volt DC to System RJ12 6 Way modular socket

    LIU Micro
    Weight: kg
    Larger picture

    Multi-Purpose Line Isolation Unit

    Buy 50+ Discount Price $8 Each Ex GST

    LIU Suitable for 'Music on Hold' and 'Public Address' RJ Sockets ( Changeable cords ) A tiny 54x26x24mm, Grey Colour.

    Cords available are; 3.5Mono - 3.5 Stereo - RCA - RJ12 - 6.3mm Phono.   Please specify your cord requirement. There are some limitations.

    If NOT specified we will supply 3.5 Stereo on the Music end and RJ12 on the system end.  

    Specifications:

    Limiting: 2.8V Peak to Peak when Terminated with 600ohms 
    Freq. Response: 20 to 20kHz - designed to minimise distortion.
    Input Attenuation: Selectable via volume control
    Safety Isolation: 3000V
    Connections:
      Music Input: RJ11 Socket 4P2C to 3.5mm stereo plug, with 400mm cable ( Standard ) See options
      Output: 6 Way modular socket